Skip to content

Free · runs in your browser · no app

Fix My Speaker: Eject Water & Dust

Water in phone speaker? Play a 165 Hz water eject sound to help clear trapped droplets, or a 200 Hz tone to loosen dust, in about 30 seconds.

Speaker cleaner

Ready, press Play to start

Volume to max · speaker facing down · headphones unplugged

Tones are generated on your device with the Web Audio API. Nothing is recorded or uploaded. Stop if you hear rattling or distortion and lower the volume.

By Nayeem, Software Developer of fastsavemedia.comLast reviewed

How to fix your phone speaker in 3 steps

  1. Turn the volume up

    Unplug headphones and disconnect Bluetooth so the tone plays through the speaker you want to clear.

  2. Point the speaker down

    Gravity helps. Hold the phone face-down or speaker-down over a towel.

  3. Press Play and repeat if needed

    Auto mode plays 165 Hz and 145 Hz water tones and a sweep. Run 2–3 cycles if sound is still muffled.

Phone held face-down over a towel while sound waves push water droplets out of the bottom speaker grille
Hold the speaker facing down so gravity helps the tone push water out of the grille.
Infographic: four steps for water in a phone speaker. 1 unplug and dry the outside, 2 hold the port facing down and tap gently, 3 optionally play the 165 Hz tone in short bursts, 4 air-dry and wait before charging. Avoid heat, compressed air, swabs or pins, rice and charging while wet.
Water in a phone speaker, step by step. The tone is optional and may only move droplets near the grille.

Real test: dust mode on an Android phone

Recorded by Nayeem on his own Android phone: the phone sits over white paper with this page open, Dust mode plays, and loose dust visibly moves off the speaker grille. 30 seconds, sound on. Results depend on how packed the debris is; stuck grime still needs a soft brush.

Fix my speaker by device

Water damage guides

Water trapped in the speaker, ports or the whole phone.

Speaker cleaning guides

Dust, lint and grime by device and by tool.

Repair & diagnostics guides

No sound, muffled, crackling or silent calls.

Audio tools guides

Cleaning sounds, audio tests and tone generation.

Which frequency does what: acoustic matrix

Speaker cleaner frequencies compared by target driver, physical mechanism, best use and timing
FrequencyTarget driverPhysical mechanismBest forIn the tool
165 HzPhone bottom loudspeakers (iPhone, Android)Long diaphragm strokes break the surface tension holding droplets on the meshWater after a splash~30 s per cycle
145 HzLarger drivers (tablets, laptops, portable speakers)Lower pitch moves more air through bigger grillesWater in larger speakersPart of Auto water cycle
200 HzSmall speakers and earpiece grillesFaster vibration shakes loose dry dust and lintDust and pocket lintDust mode
100–200 Hz sweepAny speakerGliding pitch passes through each driver's own resonance pointMixed or unknown causeEnds each Auto cycle

Safety limit: these tones stay inside the range speakers already play with music. If you hear buzzing, rattling or harsh distortion, lower the volume, and never use a tone on a phone that is still wet inside or will not power on.

Sound tone vs. common DIY fixes

MethodWaterDust / lintRiskTime
Sound tone (this tool)Shakes droplets off the meshLoose dust onlyLow at normal volume30–90 seconds
Rice or silica bagOnly slow surface dryingNoRice dust can enter portsDays
Hair dryer (hot air)Can push water deeperNoHeat can soften adhesivesMinutes
Compressed airForces water inwardSometimesCan tear the meshSeconds
Pin or cotton swabPartlyPartlyHigh, punctures meshMinutes

A tone only reaches water and dust sitting on the outer mesh. Water inside the phone needs proper drying, see water-damaged phone recovery.

Cross-section of a phone loudspeaker showing magnet, voice coil, diaphragm and the mesh grille shedding water droplets
A tone may move some droplets near a speaker; it cannot establish that a wet phone is dry or safe to use.

Frequently asked questions

How does a sound wave get water out of a speaker?

A low tone around 165 Hz makes the speaker's diaphragm move a long way back and forth. That movement breaks the surface tension holding droplets on the protective mesh and pushes them outward. Apple Watch's Water Lock eject uses the same idea.

Is it safe for my phone or earbuds?

The tone uses your device's normal audio output, the same range the speaker handles playing music. If you hear rattling or harsh distortion, lower the volume. A tone cannot fix corrosion or a torn speaker.

Which frequency should I use, 165, 145 or 200 Hz?

165 Hz suits most phone speakers. 145 Hz suits larger drivers such as portable Bluetooth speakers. 200 Hz is meant for loosening dust and lint rather than water. Auto mode picks a sequence for you.

How long should I play the water eject sound?

One cycle (about 30 seconds) usually helps after a splash. After full submersion, power the phone off and dry it first, then run two or three cycles with short pauses.

Does it work on Android, iPhone, Windows and Mac?

Yes. It runs in any modern browser using the Web Audio API. Vibration patterns only work in Android browsers; on iPhone the low rumble tone is used instead.

What should I do first if there is water in my phone speaker?

Wipe the phone, unplug any charger and do not charge it while wet. Shake out loose water with the speaker facing down, then play the water eject sound at a comfortable volume. If the phone was fully submerged, follow the manufacturer's drying guidance before using any tone.

Why not use rice or a hair dryer?

Rice only dries slowly and can leave starch dust in ports. Hot air can push water deeper and soften adhesives, and compressed air can force water inward or tear the mesh. Gravity plus a low tone acts only on water at the grille, without heat or pressure.

Is anything recorded or uploaded?

No. The tones are generated on your device. The tool never uses your microphone and sends nothing to a server.